?2012 littelfuse, inc. specifcations are subject to change without notice. transient voltage suppression diodes 1 revised: december 12, 2012 tvs diode arrays (spa ? family of products) tpsma6l series surface mount C 600w > tpsma6l series please refer to http://www.littelfuse.com for current information. description features maximum ratings and thermal characteristics (t a =25 o c unless otherwise noted) parameter symbol value unit peak pulse power dissipation at t a =25oc by 10x1000s waveform (fig.2)(note 1), (note 2) p ppm 600 w power dissipation on infnite heat sink at t a =50 o c p m(av) 3 w peak forward surge current, 8.3ms single half sine wave (note 3) i fsm 60 a maximum instantaneous forward voltage at 25a for unidirectional only v f 3.5v v operating junction and storage temperature range t j , t stg -65 to 150 c typical thermal resistance junction to lead r ujl 35 c/w typical thermal resistance junction to ambient r uja 200 c/w notes: 1. non-repetitive current pulse, per fig.4 and derated above t a =25oc per fig. 3. 2. mounted on 5.0x5.0mm copper pad to each terminal. 3. measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only. the tpsma6l series is designed specifcally to protect sensitive electronic equipment from voltage transients induced by load dump and other transient voltage events, and its especially suitable for high reliability and automotive applications. sma low profle package (do221-ac) has the same electrical performance as the smb package but with low height profles (1.1mm). applications tvs devices are ideal for the protection of i/o interfaces, v cc bus and other vulnerable circuits used in telecom, computer, industrial and consumer electronic applications. ? hi reliability application and automotive grade aec-q101 qualifed ? sma low profle package: less than 1.1 mm ? same power as standard smb devices (600 w) ? footprint compatibility with standard sma and smb products (easy to lay out) ? typical failure mode is short from over-specifed volt age or current ? whisker test is conducted based on jedec jesd201a per its table 4a and 4c ? iec-61000-4-2 esd 15kv(air), 8kv (contact) ? esd protection of data lines in accordance with iec 61000-4-2 (iec801-2) ? eft protection of data lines in accordance with iec 61000-4-4 (iec801-4) ? lo w inductance, excellent clamping capability ? fast response time: typically less than 1.0ns from 0 volts to v br min ? built-in strain relief ? glass passivated junction ? typical i r less than 1a above 12v ? high temperature soldering: 260c/40 seconds at terminals ? typical maximum temperature coeffcient v br = 0.1% x v br @25c x t ? matte tin leadCfree plated ? halogen free and rohs compliant rohs tpsma6l series functional diagram bi-directional uni-directional cathode anode uni-directional
?2012 littelfuse, inc. specifcations are subject to change without notice. transient voltage suppression diodes 2 revised: december 12, 2012 tvs diode arrays (spa ? family of products) tpsma6l series surface mount C 600w > tpsma6l series please refer to http://www.littelfuse.com for current information. electrical characteristics part number (uni) marking reverse stand-off voltage v r (volts) breakdown voltage v br (volts) @ i t test current i t (ma) maximum clamping voltage v c @ i pp (v) maximum peak pulse current i pp (a) maximum reverse leakage i r @ v r (a) min max tpsma6l5.0a aea 5.0 6.40 7.00 10 9.2 65.3 800 tpsma6l6.0a aga 6.0 6.67 7.37 10 10.3 58.3 800 tpsma6l6.5a aka 6.5 7.22 7.98 10 11. 2 53.6 500 tpsma6l7.0a ama 7. 0 7.78 8.60 10 12.0 50.0 200 tpsma6l7.5a apa 7. 5 8.33 9.21 1 12.9 46.6 100 tpsma6l8.0a ara 8.0 8.89 9.83 1 13.6 44.2 50 tpsma6l8.5a ata 8.5 9.44 10.40 1 14.4 41.7 20 tpsma6l9.0a ava 9.0 10.00 11.10 1 15.4 39.0 10 tpsma6l10a axa 10.0 11.10 12.30 1 1 7. 0 35.3 5 tpsma6l11a aza 11. 0 12.20 13.50 1 18.2 33.0 1 tpsma6l12a bea 12.0 13.30 14.70 1 19.9 30.2 1 tpsma6l13a bga 13.0 14.40 15.90 1 21.5 28.0 1 tpsma6l14a bka 14.0 15.60 17.20 1 23.2 25.9 1 tpsma6l15a bma 15.0 16.70 18.50 1 24.4 24.6 1 tpsma6l16a bpa 16.0 17.80 19.70 1 26.0 23.1 1 tpsma6l17a bra 1 7. 0 18.90 20.90 1 27.6 21.8 1 tpsma6l18a bta 18.0 20.00 22.10 1 29.2 20.6 1 tpsma6l20a bva 20.0 22.20 24.50 1 32.4 18.6 1 tpsma6l22a bxa 22.0 24.40 26.90 1 35.5 16.9 1 tpsma6l24a bza 24.0 26.70 29.50 1 38.9 15.5 1 tpsma6l26a cea 26.0 28.90 31.90 1 42.1 14.3 1 tpsma6l28a cga 28.0 31.10 34.40 1 45.4 13.3 1 tpsma6l30a cka 30.0 33.30 36.80 1 48.4 12.4 1 tpsma6l33a cma 33.0 36.70 40.60 1 53.3 11. 3 1 tpsma6l36a cpa 36.0 40.00 44.20 1 58.1 10.4 1 tpsma6l40a cra 40.0 44.40 49.10 1 64.5 9.3 1 tpsma6l43a cta 43.0 47.80 52.80 1 69.4 8.7 1 tpsma6l45a cva 45.0 50.00 55.30 1 72.7 8.3 1 tpsma6l48a cxa 48.0 53.30 58.90 1 77.4 7. 8 1 tpsma6l51a cza 51.0 56.70 62.70 1 82.4 7. 3 1 tpsma6l54a rea 54.0 60.00 66.30 1 87.1 6.9 1 tpsma6l58a rga 58.0 64.40 71.20 1 93.6 6.5 1 TPSMA6L60A rka 60.0 66.70 73.70 1 96.8 6.2 1 tpsma6l64a rma 64.0 71.10 78.60 1 103.0 5.9 1 tpsma6l70a rpa 70.0 77.80 86.00 1 113.0 5.3 1 tpsma6l75a rra 75.0 83.30 92.10 1 121.0 5.0 1 tpsma6l78a rta 78.0 86.70 95.80 1 126.0 4.8 1 tpsma6l85a rva 85.0 94.40 104.00 1 137.0 4.4 1 (t a =25c unless otherwise noted)
?2012 littelfuse, inc. specifcations are subject to change without notice. transient voltage suppression diodes 3 revised: december 12, 2012 tvs diode arrays (spa ? family of products) tpsma6l series surface mount C 600w > tpsma6l series please refer to http://www.littelfuse.com for current information. i-v curve characteristics vc v br v r i r i t i pp v uni-directional v f p ppm peak pulse power dissipation -- max power dissipation v r stand-off voltage -- maximum voltage that can be applied to the tvs without operation v br breakdown voltage -- maximum current that fows though the tvs at a specifed test current (i t ) v c clamping voltage -- peak voltage measured across the suppressor at a specifed ippm (peak impulse current) i r reverse leakage current -- current measured at v r v f forward voltage drop for uni-directional 0. 1 1 10 100 0.00000 10 . 00001 0. 0 001 0.00 1 t d -pulse width (sec.) 0.2x0.2" (5.0x5.0mm) copper pad area p ppm -peak pulse power (kw) figure 2 - peak pulse power rating curve vo lt age tr an si en ts ti me vo lt age acro ss tv s current through tvs voltage or current figure 1 - tvs transients clamping waveform ratings and characteristic curves (t a =25c unless otherwise noted) continues on next page.
?2012 littelfuse, inc. specifcations are subject to change without notice. transient voltage suppression diodes 4 revised: december 12, 2012 tvs diode arrays (spa ? family of products) tpsma6l series surface mount C 600w > tpsma6l series please refer to http://www.littelfuse.com for current information. 0 20 40 60 80 100 02 5507 51 00 12 51 50 17 5 t a -a mb ie nt te mp erat ur e (oc) peak pulse power (p pp ) or current (i pp ) derating in percentage % 1 10 100 1000 1000 0 1. 0 10. 01 00. 01 000. 0 cj (p f) tj =2 5o c f= 1.0m hz vs ig =5 0m vp -p un i- di re ct i onal v= 0v un i- di re ct io nal @v r v br - reverse breakdown vo ltage (v) figure 3 - pulse derating curve i ppm - peak pulse current, % i rsm 0 0 50 10 0 15 0 1. 0 2.0 3.0 4.0 t r =10sec peak value i ppm i ppm 2 t j =25c pulse width(td) is de?ned as the point where the peak current decays to 50% of i ppm 10/1 00 0sec. waveform as de?ned by r.e.a t d t-time (ms) half value i ppm ( ) figure 4 - pulse waveform figure 5 - typical junction capacitance 02 5507 5 100 125 150 175 p m(av) , steady state power dissipation (w) t a - ambient te mperature (oc) ba rg ai ni ng 3.0 0.6 1.2 1.8 3.6 2.4 0 ruja=rujl ruja=200c/w figure 6 - steady state power dissipation derating curve ratings and characteristic curves (t a =25c unless otherwise noted) (continued)
?2012 littelfuse, inc. specifcations are subject to change without notice. transient voltage suppression diodes 5 revised: december 12, 2012 tvs diode arrays (spa ? family of products) tpsma6l series surface mount C 600w > tpsma6l series please refer to http://www.littelfuse.com for current information. dimensions physical specifcations weight 0.002 ounce, 0.061 gram case jedec do-221ac molded plastic over glass passivated junction polarity color band denotes cathode except bipolar terminal matte tin-plated leads, solderable per jesd22-b102d dimensions inches millimeters min max min max a 0.156 0.181 3.950 4.600 b 0.189 0.220 4.800 5.600 c 0.049 0.069 1.250 1.750 d 0.088 0.116 2.250 2.950 e 0.030 0.059 0.750 1.500 f 0.005 0.010 0.125 0.250 g 0.035 0.043 0.900 1. 10 0 environmental specifcations temperature cycle jesd22-a104 pressure cooker jesd22-a102 high temp. storage jesd22-a103 htrb jesd22-a108 thermal shock jesd22-a106 soldering parameters temperature (t) ti me (t) t s(min) t s(max) t l t p t s preheat t l t p ramp-up critical zone t l to t p ramp-down t 25?c to peak 25?c refow condition leadCfree assembly pre heat - temperature min (t s(min) ) 150c - temperature max (t s(max) ) 200c - time (min to max) (t s ) 60 C 180 secs average ramp up rate (liquidus temp (t l ) to peak 3c/second max t s(max) to t l - ramp-up rate 3c/second max refow - temperature (t l ) (liquidus) 217c - time (min to max) (t s ) 60 C 150 seconds peak temperature (t p ) 260 +0/-5 c time within 5c of actual peak temperature (t p ) 20 C 40 seconds ramp-down rate 6c/second max time 25c to peak temperature (t p ) 8 minutes max. do not exceed 280c d 3.12 (0.123) 1. 20 (0.047) 1. 52 (0.060) mounting pad layout a b e e c g f cathode band
?2012 littelfuse, inc. specifcations are subject to change without notice. transient voltage suppression diodes 6 revised: december 12, 2012 tvs diode arrays (spa ? family of products) tpsma6l series surface mount C 600w > tpsma6l series please refer to http://www.littelfuse.com for current information. part numbering system part marking system packaging part number component package quantity packaging option packaging specifcation tpsma6lxxa do-221ac 3000 tape & reel C 12mm/7 tape eia rs-481 tpsma6l xx a series 5% v br vo lta ge tolerance v r vo lta ge tape and reel specifcation 0.47 (12.0) 0.157 (4.0) 0.157 (4.0) 0.49 (12.5) 0.80 (20.2) arbor hole dia. 7.0 (178) dimensions are in inches (and millimeters). direction of feed 0.059 dia (1.5) cover tape cathode f xxx ymxxx marking code trace code marking y:year code m: month code xxx: lot code littelfuse logo cathode band
|
